Featured Installations of our Furniture

PART 1 – GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply
to this section
1.2 SUMMARY
A. This section includes the following:
1. Common standard floor mounted chairs as detailed in Part 2 of these specifications.
1.3 SUBMITTALS
A. Product data for each type of product specified. Include installation methods.
B. Shop drawings, prepared for architectural drawings and from field dimensions, showing the seating layout,
seat numbering sequence, chair sizes, and aisle widths. Also show a section view with profile dimensions
of the seating and back-to-back dimensions.
C. Samples for initial selection purposes in the form of manufacturer’s color charts or samples of materials
showing the full range of standard colors, finishes, and patterns.
1. Fabric
2. Metal Finishes
3. Wood Finishes
D. Statement signed by the theater seating manufacturer confirming that the products submitted comply with
the specified requirements.
1.4 QUALITY ASSURANCE
A. Provide installer’s qualifications confirming the installer is qualified to install the manufacturer’s chairs
B. Provide seating that complies with California Technical Bulletin 117.
C. Obtain each type of seating, including accessories and mounting components, from a single manufacturer.
D. Design and install seating with end standards aligning from first to last row and with backs and seats varied
in width to optimize sightlines. Comply with ADA rules and regulations.
1.5 PROJECT CONDITIONS
A. Environmental Conditions: Do not install seating until space is enclosed and weatherproof, wet work in
space is complete and dry, installation of finishes including painting is complete, and ceilings are complete.
Do not install seating until ambient temperature and humidity conditions are continuously maintained at
final occupancy values.
1.6 DELIVERY, STORAGE, AND HANDLING
A. Deliver seating in manufacturer’s unopened cartons clearly labeled with manufacturer’s name and
contents.
B. Handle seating in manner to prevent damage.
1.7 EXTRA MATERIALS
A. Furnish from the same production run as the materials installed. Package materials with protective
covering and identify with labels describing contents.
1. Seat and back covers to be furnished in a quantity equal to 5 percent of the amount of chairs
installed.
PART 2 – PRODUCTS
2.1 SEATING
A. Provide from Navetta division of Shuttlesystem LLC, corporate headquarters 7697 Innovation Way,
Suite 400 Mason, OH 45040, manufacturing plant 1330 Potts Ave, High Point, NC 27260, the Teatro
“A1” model as follows:
1. Basic floor mounted chair.
2. Inner upholstered seat and back.
Teatro A1 Specifications – Theatre Seating
Page 2 of 5
3. Outer wood veneer seat and back with stained edges.
4. Wood armrests.
5. Aisle lights where indicated on the drawings.
6. Wood veneer end panels where indicated on the drawings.
B. Model noted is based on the Navetta. Teatro “A1” model with the intent of establishing the high level of
quality required for the project. Other brands submitted for approval will be given consideration provided
that a full seating mock-up, along with a complete list of specification discrepancies between the proposed
substitution and the product specified is received at least 10 working days prior to the bid date.
1. By offering a quote for this project, the bidder assumes full responsibility for complying with the
specifications for this project and shall be totally responsible for any expenses incurred if the
product quoted does not comply with the specifications.
C. Failure to comply with the warranty described in Part 4 of these specifications will be cause for
disqualification.
2.2 MATERIALS
A. Padding material shall be high resiliency polyurethane foam which conforms to the standards of the
California Bureau of Home Furnishings 117-75. The back shall be 1-3/4” thick. The seat shall be 3” thick.
B. Seating fabric shall be manufactures standard colors unless selected by architect or customer the
color to be selected from the standard choice of colors. All upholstery shall be first quality without
creases, stretch lines, or wrinkles.
C. Exposed wood on the outer back panel shall be veneer. The panel edges shall be stained to match the
veneer faces. The arms shall be solid wood. All wood shall be stained to match the architect’s sample.
2.3 FABRICATION, GENERAL
A. Fabricate the theater seating in contoured form for maximum comfort using materials that are carefully
selected to be free from defects, objectionable projections, or irregularities. Smooth round corners and
edges to present the least possible snagging and pinching hazards.
2.4 MOUNTING
A. Fabricate seating units for floor attachment, using standards that have been manufactured to conform to
the slope of the floor while maintaining seat and back in same angular relationship to standards throughout.
2.5 METAL STANDARDS
A. Frame shall be 3/4” x 2” x 16 gauge cold-rolled welded steel tubing, and 5/16” x 3” hot-rolled steel plate,
and 11 gauge formed steel brackets welded into one integral freestanding structure upon which the seat,
back, and arms are assembled. Pivot and stop pins shall be machined from cold-finished steel to
tolerances of +0.000 -0.005. Floor mount plate shall be 5/16” thick hot-rolled pickled-in-oil steel plate with
two countersunk holes for 1/4-20 mounting screws.
2.6 UPHOLSTERED CHAIRS
A. General: Fabricate theater seating with padding and fabric covering. Equip each seat with a gravity selfrising
mechanism so that unoccupied seats return to an upright position perpendicular to the base line of
floor of auditorium. Spring compensating mechanism will not be acceptable. Chair profile with the seat in
the upright position and without a tablet arm, cannot exceed 18”. The chair profile with the seat in the
upright position and with a tablet arm, cannot exceed 24”.
B. Seat Construction: Solid seat bottom construction comprised of a curved plywood veneer outer panel
fastened solidly and without voids to an inner structural plywood panel. The outer panel shall be 15mm
thick, faced one side with Grade A veneer centered across the width of the panel, and exposed plywood
laminations along the edges. The inner panel shall be 5/8” thick. Both shall be electronically glued
hardwood plywood and shall be fastened together with bayonet hanging brackets at the top and two steel
angles at the bottom, resulting in a rigid connection with no visible fasteners. The veneer face and edges
of the outer panel shall be stained to match the architect’s sample. The padding material shall be 3” thick
polyurethane foam, shall be glued to the inner panel, and shall conform to the California Bureau of Home
Furnishings Technical Bulletin 117. The complete seat assembly shall be supported by two 7 gauge
formed steel mounting brackets which will attach the seat assembly to the hinges on the standards. The
seat shall have a built-in counterweight to insure automatic self-rising without the aid of springs. Archspring
construction will not be acceptable.
Teatro A1 Specifications – Theatre Seating
Page 3 of 5
C. Back Construction: Solid back construction comprised of a curved plywood veneer outer panel fastened
solidly and without voids to an inner structural plywood panel. The outer panel shall be 15mm thick, faced
one side with Grade A veneer centered across the width of the panel, and exposed plywood laminations
along all edges. The inner panel shall be 3/8” thick. Both shall be electronically glued hardwood plywood
and shall be fastened together with bayonet hanging brackets at the top and two #8 x 3/4” trim head screws
at the bottom, resulting in a rigid connection with no visible fasteners on the outer wood panel. The veneer
face and edges of the outer panel shall be stained to match the architect’s sample. The padding material
shall be 1-3/4” thick polyurethane foam, 2-3/4” thick in the lumbar region, shall be glued to the inner panel,
and shall conform to the California Bureau of Home Furnishings Technical Bulletin 117. The complete
back assembly shall be supported by two 13 gauge formed steel brackets and two 3/8-16 hex head bolts
which will attach the back assembly to the frame.
D. Armrests: Shall be kiln-dried solid hardwood, nominally 1” thick x 2-1/2” wide x 12” long, stained to match
the outer seat and back panels. The armrest will be fastened to the steel frame arm support with one 10-
24 x 7/8” flat head machine screw and one 10-24 x 2-1/4” flat head machine screw into threaded inserts on
the underside of the armrest. Chairs equipped with tablet arms shall have armrests nominally 1” thick x 2-
1/2” wide x 18” long and shall be attached to the steel frame arm support with four #8 x 3/4” sheet metal
screws.
E. Hinge: The seat hinge shall be a weldment consisting of a 7 gauge hot-rolled pickled-in-oil steel component
and shall be formed and punched to receive a 0.56” id x 0.75” od x 0.5” long steel bushing. A selflubricating
nylon sleeve shall be fitted between the seat hinge and the standard seat hinge pin. The hinge
shall be machined to provide a positive stop location for the seat in both occupied and unoccupied
positions. The hinge shall be fitted with a plastic cover to eliminate all pinch points and shall include a
3/16” thick urethane rubber pad to dampen noise upon the seat return to the vertical position.
PART 3 – OPTIONS
3.1 END PANEL
A. Provide manufacturer’s standard end panel at the end of the row. The configuration of the panel shall
follow the angle of the frame and back at the rear, and shall be vertical at the front end. The panel shall be
constructed of 3/4” thick plywood with veneer on both sides and 1/8” thick solid wood on the vertical edges.
The end panel shall be stained to match the outer wood seat, back, and armrests.
3.2 AISLE LIGHT
A. Aisle lights shall be provided in accordance to the locations shown on the architectural drawings. The units
shall be of low voltage (24v) type and the light tube shall fit into a routed area on the underside of the
armrest. The chair frame shall be prepared to accept the power wire. The necessary access holes and
blank cover plates shall be provided. The chair manufacturer shall also provide the necessary
transformers. All wiring and electrical connections shall be conducted at the job site and shall be the
responsibility of others.
3.3 HARDWOOD EDGES, OUTER SEAT AND BACK
A. Outer plywood panels shall be trimmed in 1/8” thick hardwood on the top and vertical edges. The
hardwood shall match the face veneer species and be stained to match.
3.4 INSET UPHOLSTERY, BACK
A. Back Upholstery shall be inset to expose the veneer face on the inside of the outer back panel. The veneer
on the inside face on the back panel shall match the veneer species on the outside face and be stained to
match.
3.5 SEAT AND ROW IDENTIFICATION TAGS
A. Provide manufacturer’s standard shape brass number and letter plates. Font shall be Times Roman. The
size of the font on the seat number plates shall be 27pt; the size of the font on the row letter plates shall be
42pt. The number plates shall fit into a recessed area at the top edge of the seat. The row letter plates
shall fit into a recessed area at the back of the armrest.
3.6 REMOVABLE CHAIR
A. Provide manufacturer’s standard one, two, or three chair removable units which shall include an integrated
steel sled-base that is engineered to conform to the row radii and includes two through holes per chair for
floor mounting.
3.7 FREESTANDING REMOVABLE CHAIR
Teatro A1 Specifications – Theatre Seating
Page 4 of 5
A. Provide manufacturer’s standard freestanding removable chair which shall include an integrated steel sledbase
that is engineered to conform to the row radii and includes extended length floor plates to allow the
chairs to remain stable with no physical attachment to the floor.
3.8 TABLET ARMS
A. Tablet arm shall be two-motion fold-away style, constructed of 1/2” medium density fiberboard, faced two
sides with matte black high-pressure laminate. The edges shall be finished with a vinyl T-molding trimmed
flush with both top and bottom surfaces.
3.9 POWER/DATA
A. Where indicated on the drawings, chair frames shall be equipped with a 115v/15amp power outlet and a
RJ-45 Category 6 data port located on the front of the armrest gusset. Wire raceways shall be provided for
routing of the wires from chair to chair. All wiring and electrical connections shall be conducted at the job
site and shall be the responsibility of others.
3.10 BOOKRACKS
A. The bookrack shall be constructed of hardwoods and hardwood plywood. Bookrack shall be assembled
with tongue and groove construction and finished with a catalyzed lacquer. The bookrack shall be attached
to the outer surface of the chair back. An optional attachment configuration shall consist of a steel
weldment attached to the chair leg. This configuration allows the bookrack to be located between chair
backs.
3.11 COMPLIANCE WITH CALIFORNIA TECHNICAL BULLETIN 133
PART 4 – WARRANTY
4.1 The theater seating manufacturer must provide a Lifetime Warranty to the original purchaser of the seating as
follows:
A. The seating manufacturer shall warrant it’s products against failures and manufacturing defects for the life
of the product. This warranty applies to the original purchaser and is non-transferable. The seating
manufacturer will provide parts and labor to replace defective parts for the first two years after the
installation. Thereafter, the manufacturer will provide replacement parts for the life of the product.
B. This warranty shall not cover damage from abuse, misuse, neglect, or act of God. Damage caused by
modifications to the product by anyone other than a Navetta authorized seating installation technician will
void this warranty. This warranty does not apply to fabrics or products not installed by Navetta authorized
seating installation technicians.
PART 5 – EXECUTION
5.1 EXAMINATION
A. Examine site conditions, with installer present, for compliance with requirements for construction tolerances
as they affect anchors and fasteners, and location of junction boxes.
B. Do not proceed until unsatisfactory conditions have been corrected.
5.2 GENERAL
A. Comply with seating manufacturer’s printed installation instructions applicable to products.
B. Locate seating in locations indicated on approved shop drawings, with required clearances.
C. Install standards in locations conforming to seating layout, with each standard attached to substrate by no
less than two anchoring devices of size and type required to insure that chairs are stable under conditions
of actual use.
D. Install chairs using manufacturer’s recommended hardware and fasteners. Insure that chairs in curved
rows are installed on proper radius and are oriented toward the center point of the radius. Verify that
moving components operate smoothly and quietly.
5.3 ADJUSTING
A. Adjust as required to assure that the seats in each row are aligned when in the upright position.
B. Touch-up minor abrasions and imperfections in painted finishes with coating that matches factory-applied
finish.
Teatro A1 Specifications – Theatre Seating
Page 5 of 5
C. Replace any upholstery that has been damaged during installation.
END OF SPECIFICATION

Download Teatro A1 Spec
Download Teatro C1 Spec
Download Teatro C3 Spec

PART 1 – GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply
to this section
1.2 SUMMARY
A. This section includes the following:
1. Common standard floor mounted chairs as detailed in Part 2 of these specifications.
1.3 SUBMITTALS
A. Product data for each type of product specified. Include installation methods.
B. Shop drawings, prepared for architectural drawings and from field dimensions, showing the seating layout,
seat numbering sequence, chair sizes, and aisle widths. Also show a section view with profile dimensions
of the seating and back-to-back dimensions.
C. Samples for initial selection purposes in the form of manufacturer’s color charts or samples of materials
showing the full range of standard colors, finishes, and patterns.
1. Fabric
2. Metal Finishes
3. Wood Finishes
4. Plastic Finishes
D. Statement signed by the theater seating manufacturer confirming that the products submitted complies with
the specified requirements.
1.4 QUALITY ASSURANCE
A. Provide installer’s qualifications confirming the installer is qualified to install the manufacturer’s chairs
B. Provide seating that complies with California Technical Bulletin 117.
C. Obtain each type of seating, including accessories and mounting components, from a single manufacturer.
D. Design and install seating with end standards aligning from first to last row and with backs and seats varied
in width to optimize sightlines. Comply with ADA rules and regulations.
1.5 PROJECT CONDITIONS
A. Environmental Conditions: Do not install seating until space is enclosed and weatherproof, wet work in
space is complete and dry, installation of finishes including painting is complete, and ceilings are complete.
Do not install seating until ambient temperature and humidity conditions are continuously maintained at
final occupancy values.
1.6 DELIVERY, STORAGE, AND HANDLING
A. Deliver seating in manufacturer’s unopened cartons clearly labeled with manufacturer’s name and
contents.
B. Handle seating in a manner to prevent damage.
1.7 EXTRA MATERIALS
A. Furnish from the same production run as the materials installed. Package materials with protective
covering and identify with labels describing contents.
1. Seat and back covers to be furnished in a quantity equal to 5 percent of the amount of chairs
installed.
PART 2 – PRODUCTS
2.1 SEATING
A. Provide from Navetta division of Shuttlesystem LLC, corporate headquarters 7697 Innovation Way, Suite
400 Mason, OH 45040, manufacturing plant 1330 Potts Ave, High Point, NC 27260, the Lyric “D1” model
as follows:
1. Basic floor mounted chair
Lyric D1 Specifications – Theatre Seating
Page 2 of 2
2. Inner upholstered seat and back
3. Outer wood veneer back with stained edges
4. Outer injection-molded plastic seat cover
5. Blow-molded plastic armrests
6. Aisle lights where indicated on the drawings
7. End panels where indicated on the drawings
B. Model noted is based on the Navetta Lyric “D1” model with the intent of establishing the high level of quality
required for the project. Other brands submitted for approval will be given consideration provided that a full
seating mock-up, along with a complete list of specification discrepancies between the proposed
substitution and the product specified is received at least 10 working days prior to the bid date.
1. By offering a quote for this project, the bidder assumes full responsibility for complying with the
specifications for this project and shall be totally responsible for any expenses incurred if the
product quoted does not comply with the specifications.
C. Failure to comply with the warranty described in Part 4 of these specifications will be cause for
disqualification.
2.2 MATERIALS
A. Padding material shall be high resiliency polyurethane foam which conforms to the standards of the
California Bureau of Home Furnishings 117-75. The back shall be 1 1/4” thick. The seat shall be 1 3/4”
thick.
B. Seating fabric shall manufactures standard colors unless selected by architect or customer the color to
be selected from the standard choice of colors. All upholstery shall be first quality without creases,
stretch lines, or wrinkles.
C. Exposed wood on the outer back panel shall be veneer. The panel edges shall be stained to match the
veneer faces. All wood shall be stained to match the architect’s sample. The outer plastic cover shall be
impact resistant polypropylene. The arms shall be high density polyethylene.
2.3 FABRICATION, GENERAL
A. Fabricate the theater seating in contoured form for maximum comfort using materials that are carefully
selected to be free from defects, objectionable projections, or irregularities. Insure smooth round corners
and edges to present the least possible snagging and pinching hazards.
2.4 MOUNTING
A. Fabricate seating units for floor attachment, using standards that have been manufactured to conform to
the slope of the floor while maintaining seat and back in same angular relationship to standards throughout.
2.5 METAL STANDARDS
A. Frame shall be 3/4” x 2” x 16 gauge cold-rolled welded steel tubing; 1/4” x 3 1/2” hot-rolled steel plate, 1/4”
x 2 1/8” hot-rolled steel plate and 11 gauge formed steel brackets welded into one integral freestanding
structure upon which the seat, back, and arms are assembled. Pivot and stop pins shall be machined from
cold-finished steel to tolerances of +0.000 -0.005. Floor mount plate shall be .100” thick hot-rolled pickledin-
oil steel formed and embossed for 1/4” mounting anchors. A molded plastic cap shall be fitted into the
embossed mounting area to conceal the anchoring hardware. Exposed floor anchoring hardware will not
be acceptable.
2.6 UPHOLSTERED CHAIRS
A. General: Fabricate theater seating with padding, fabric covering and injection-molded seat cover. Equip
each seat with a gravity self-rising mechanism so that unoccupied seats return to an upright position
perpendicular to the base line of floor of auditorium. Spring compensating mechanism will not be
acceptable. Chair profile with the seat in the upright position and without a tablet arm, cannot exceed 18”.
Lyric D1 Specifications – Theatre Seating
Page 3 of 3
B. Seat Construction: Seat construction is comprised of an injection-molded polypropylene cover fastened
securely to an inner upholstered structural steel frame assembly. The outer seat cover shall have a
textured exterior surface and internal molded reinforcing ribs for a solid warp-free construction. The inner
seat frame assembly shall consist of a 7/8” dia. X 16 gauge steel tube formed with a waterfall front edge
and welded into a rigid assembly with (2) 11 gauge X 1” steel brackets and (1) 1/4” diameter steel rod. The
seat frame shall be fitted with a cast iron counterweight to insure automatic self-rising without the aid of
springs. A series of (7) 2” wide elastic suspension straps shall be stretched and woven in place and
fastened to the steel seat frame with 1/8” dia. steel hooks. Arch-spring and/or S-spring construction will not
be acceptable. A layer of 1 3/4” thick molded polyurethane foam shall be applied over the elastic webbing.
Foam shall be fire retardant and conform to the California Bureau of Home Furnishings Technical Bulletin
117. The upholstery cover shall be sewn and fitted to the seat assembly with collapsible assembly rings
and nylon tension cord.
The outer injection-molded seat cover and upholstered inner seat assembly shall be joined together with
cast aluminum mounting brackets. Seat widths of 19” and 21” shall be fitted with narrow style mounting
brackets. Seat widths of 20” and 22” shall be fitted with width-extending mounting brackets. The complete
seat assembly shall be assembled to the seat hinges using (2) special purpose M10 Hinge Bolts and (2)
special purpose M10 Hinge Pins which are specifically designed to accommodate installation tolerances.
C. Back Construction: Back construction is comprised of a curved plywood veneer outer panel fastened solidly
and without voids to an inner structural plywood panel. The outer panel shall be 15mm thick, faced one
side with Grade A veneer centered across the width of the panel, and exposed plywood laminations along
all edges. The inner panel shall be 3/8” thick. Both shall be electronically glued hardwood plywood and
shall be fastened together with bayonet hanging brackets at the top and two #8 x 3/4” trim head screws at
the bottom, resulting in a rigid connection with no visible fasteners on the outer wood panel. The veneer
face and edges of the outer panel shall be stained to match the architect’s sample. The padding material
shall be 1-3/4” thick polyurethane foam (2-3/4” thick in the lumbar region), shall be glued to the inner panel
and shall conform to the California Bureau of Home Furnishings Technical Bulletin 117. The complete
back assembly shall be supported by two 13 gauge formed steel brackets and two 3/8-16 hex-head bolts
and shall be attached to the frame with (2) 1/4-20 machine screws.
D. Armrests: Shall be blow-molded of high density polyethylene and curved to match the leg mounting plate.
The armrest shall be fastened to the steel frame arm support with three #8 sheet metal screws.
E. Hinge: Shall be injection-molded of DuPont™ Zytel® 801 nylon. The hinge shall be molded with
provisions to provide positive stop locations for the seat in both occupied and unoccupied positions. The
hinge shall be fitted with a plastic cover to eliminate all pinch points and shall include (2) 7/16” thick
urethane rubber pads to dampen noise upon the seat stop in both the vertical and horizontal positions.
Note: Dupont™ and Zytel ®are registered trademarks of E.I.du Pont de Nemours and Co. or its affiliates
PART 3 – OPTIONS
3.1 VENEER END PANEL
A. Provide manufacturer’s standard end panel at the end of the row. The configuration of the panel shall
follow the angle of the frame and back at the rear, and shall be vertical at the front edge. The panel shall
be constructed of 3/4” thick plywood with veneer on both sides and 1/8” thick solid wood on the vertical
edges. The end panel shall be stained to match the outer wood seat, back, and armrests.
3.2 POWDER-COATED END PANEL
A. Provide manufacturer’s standard end panel at the end of the row. The configuration of the panel shall
follow the angle of the frame and back at the rear, and shall be vertical at the front edge. The panel shall
be constructed of 3/4” thick medium density fiberboard with a durable powder-coated black finish.
3.3 AISLE LIGHT
A. Aisle lights shall be provided in accordance to the locations shown on the architectural drawings. The
units shall be of low voltage (24v) type and the light tube shall fit into a recessed area on the underside of
the armrest. The chair frame shall be prepared to accept the power wire. The necessary access holes
and blank cover plates shall be provided. The chair manufacturer shall also provide the necessary
transformers. All wiring and electrical connections shall be conducted at the job site and shall be the
responsibility of others.
3.4 SEAT IDENTIFICATION TAGS
Lyric D1 Specifications – Theatre Seating
Page 4 of 4
A. Provide manufacturer’s standard shape polycarbonate number plates. Font shall be Times Roman. The
number plates shall fit into a recessed area at the top edge of the seat and shall be adhered with highstrength
pressure-sensitive tape.
3.5 ROW IDENTIFICATION AND DONOR TAGS
A. Provide manufacturer’s standard shape polycarbonate letter plates. Font shall be Times Roman.
3.6 REMOVABLE CHAIR
A. Provide the manufacturer’s standard one, two or three chair Removable units which shall include an
integrated steel sled-base that is engineered to conform to the row radii and includes two through holes
per chair for floor mounting.
3.7 FREESTANDING REMOVABLE CHAIR
A. Provide manufacturer’s standard freestanding removable chair which shall include an integrated steel
sled-base that is engineered to conform to the row radii and includes extended length floor plates to allow
the chairs to remain stable with no physical attachment to the floor.
3.8 BOOKRACK
A. The bookrack shall be constructed of hardwoods and hardwood plywood. Bookrack shall be assembled
with tongue and groove construction and finished with a catalyzed lacquer. The bookrack shall be
attached to the outer surface of the chair back. An optional attachment configuration shall consist of a
steel weldment attached to the chair leg. This configuration allows the bookrack to be located between
chair backs.
3.9 FLAT WOOD ARMREST
A. Shall be kiln-dried solid hardwood, nominally 1” thick x 2-1/2” wide x 12” long, stained to match the outer
back panel. The armrest will be fastened to the steel frame arm support with one 10-24 x 7/8” flat head
machine screw and one 10-24 x 2-1/4” flat head machine screw into threaded inserts on the underside of
the armrest.
3.10 CURVED WOOD ARMREST
A. Shall be kiln-dried solid hardwood, nominally 1 1/8” thick x 2 1/4” wide x 12 3/4“ long, stained to match the
outer back panel. The armrest will be fastened to the steel frame arm support with three #8 x 5/8” pan
head sheet metal screws.
PART 4 – WARRANTY
4.1 The theater seating manufacturer must provide a Lifetime Warranty to the original purchaser of the seating as
follows:
A. The seating manufacturer shall warrant its products against failures and manufacturing defects for the life
of the product. This warranty applies to the original purchaser and is non-transferable. The seating
manufacturer will provide parts and labor to replace defective parts for the first two years after the
installation. Thereafter, the manufacturer will provide replacement parts for the life of the product.
B. This warranty shall not cover damage from abuse, misuse, neglect, or act of God. Damage caused by
modifications to the product by anyone other than a Navetta authorized seating installation technician will
void this warranty. This warranty does not apply to fabrics or products not installed by Navetta authorized
seating installation technicians.
PART 5 – EXECUTION
5.1 EXAMINATION
A. Examine site conditions, with installer present, for compliance with requirements for construction tolerances
as they affect anchors and fasteners, and location of junction boxes.
B. Do not proceed until unsatisfactory conditions have been corrected.
5.2 GENERAL
A. Comply with seating manufacturer’s printed installation instructions applicable to products.
B. Locate seating in locations indicated on approved shop drawings, with required clearances.
C. Install standards in locations conforming to seating layout, with each standard attached to substrate by no
less than two anchoring devices of size and type required to insure that chairs are stable under conditions
Lyric D1 Specifications – Theatre Seating
Page 5 of 5
of actual use.
D. Install chairs using manufacturer’s recommended hardware and fasteners. Insure that chairs in curved
rows are installed on proper radius and are oriented toward the center point of the radius. Verify that
moving components operate smoothly and quietly.
5.3 ADJUSTING
A. Adjust as required to assure that the seats in each row are aligned when in the upright position.
B. Touch-up minor abrasions and imperfections in painted finishes with coating that matches factory-applied
finish.
C. Replace any upholstery that has been damaged during installation.
END OF SPECIFICATION

Download Lyric D1 Spec
Download Lyric D4 Spec

“PART 1 – GENERAL”
“1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this section.
1.2 SUMMARY
A. This section includes the following:
1. Common standard floor mounted chairs as detailed in Part 2 of these specifications.
1.3 SUBMITTALS
A. Product data for each type of product specified. Include installation methods.
B. Shop drawings, prepared for architectural drawings and from field dimensions, showing the seating layout, seat numbering sequence, chair sizes, and aisle widths. Also show a section view with profile dimensions of the seating and back-to-back dimensions.
C. Samples for initial selection purposes in the form of manufacturer’s color charts or samples of materials showing the full range of standard colors, finishes, and patterns.
1. Fabric
2. Metal Finishes
3. Wood Finishes
D. Statement signed by the theater seating manufacturer confirming that the products submitted comply with the specified requirements.
1.4 QUALITY ASSURANCE
A. Provide installer’s qualifications confirming the installer is qualified to install the manufacturer’schairs
B. Provide seating that complies with California Technical Bulletin 117.
C. Obtain each type of seating, including accessories and mounting components, from a single manufacturer.
D. Design and install seating with end standards aligning from first to last row and with backs and seats varied in width to optimize sightlines. Comply with ADA rules and regulations.
1.5 PROJECT CONDITIONS
A. Environmental Conditions: Do not install seating until space is enclosed and weatherproof, wet work in space is complete and dry, installation of finishes including painting is complete, and ceilings are complete. Do not install seating until ambient temperature and humidity conditions are continuously maintained at final occupancy values.
1.6 DELIVERY, STORAGE, AND HANDLING
A. Deliver seating in manufacturer’s unopened cartons clearly labeled with manufacturer’s name and contents.
B. Handle seating in manner to prevent damage.
1.7 EXTRA MATERIALS
A. Furnish from the same production run as the materials installed. Package materials with protective covering and identify with labels describing contents.
1. Seat and back covers to be furnished in a quantity equal to 5 percent of the amount of chairs installed.
PART 2 – PRODUCTS
2.1 SEATING
A. Provide from Navetta division of Shuttlesystem LLC, corporate headquarters 7697 Innovation Way, Suite 400 Mason, OH 45040, manufacturing plant 1330 Potts Ave, High Point, NC 27260, the Acclaim “C1” model as follows:
1. Basic floor mounted chair.”

“2. Fully-upholstered seat.”
“3. Inner upholstered back.
4. Outer wood veneer back with stained edges.
5. Wood armrests.
6. Aisle lights where indicated on the drawings.
B. Model noted is based on the Navetta Acclaim “C1” model with the intent of establishing the high level of quality required for the project. Other brands submitted for approval will be given consideration provided that a full seating mock-up, along with a complete list of specification discrepancies between the proposed substitution and the product specified is received at least 10 working days prior to the bid date.
1. By offering a quote for this project, the bidder assumes full responsibility for complying with the specifications for this project and shall be totally responsible for any expenses incurred if the product quoted does not comply with the specifications.
C. Failure to comply with the warranty described in Part 4 of these specifications will be cause for disqualification.
2.2 MATERIALS
A. Padding material shall be flexible polyurethane foam which conforms to the standards of the California Bureau of Home Furnishings 117-75. The back shall be 2” thick. The seat shall be 3” thick.
B. Seating fabric shall be manufactures standard colors unless selected by architect or customer the color to be selected from the standard choice of colors. The inner back and seat shall be upholstered by attaching the fabric to the inside wood back and seat panels. All upholstery shall be first quality without creases, stretch lines, or wrinkles.
C. Exposed wood on the outer back panel shall be veneer. The panel edges shall be stained to match the veneer faces. The arms shall be solid wood. All wood shall be stained to match the architect’s sample.
2.3 FABRICATION, GENERAL
A. Fabricate the theater seating in contoured form for maximum comfort using materials that are carefully selected to be free from defects, objectionable projections, or irregularities. Smooth round corners and edges to present the least possible snagging and pinching hazards.
2.4 MOUNTING
A. Fabricate seating units for floor attachment, using standards that have been manufactured to conform to the slope of the floor while maintaining seat and back in same angular relationship to standards throughout.
2.5 METAL STANDARDS
A. Frame shall be 3/4” x 2” x 16 gauge cold-rolled welded steel tubing, and 5/16” x 2” hot-rolled pickled-in-oil steel strip, de-scaled and fully welded into one integral freestanding structure upon which the seat, back, and arms are assembled. Pivot and stop pins shall be machined from cold-finished steel to tolerances of
+0.000 -0.005. Floor mount plate shall be 5/16” thick cold-rolled steel plate with two countersunk holes for 1/4-20 mounting screws.
2.6 UPHOLSTERED CHAIRS
A. General: Fabricate theater seating with padding and fabric covering. Equip each seat with a gravity self- rising mechanism so that unoccupied seats return to an upright position perpendicular to the base line of floor of auditorium. Spring compensating mechanism will not be acceptable. Chair profile with the seat in the upright position and without a tablet arm, cannot exceed 15-1/2”. The chair profile with the seat in the upright position and with a tablet arm, cannot exceed 21”.
B. Seat Construction: The seat panel shall be 3/4” thick, electronically glued hardwood plywood withfour
1/4-20 threaded steel inserts for attachment of hinges. The padding material shall be 3” thick polyurethane foam, shall be glued to the inner surface of the seat panel, and shall conform to the California Bureau of Home Furnishings Technical Bulletin 117. The outside surface of the seat panel shall be encapsulated in 1/4” thick slab polyurethane foam. The seat shall have a built-in counterweight to insure automatic self-
rising without the aid of springs. Arch-spring seat construction will not be acceptable.”

“C. Back Construction: Solid back construction comprised of a curved plywood veneer outer panel fastened solidly and without voids to an inner structural plywood panel. The outer panel shall be 15mm thick, faced one side with Grade A veneer centered across the width of the panel, and exposed plywood laminations along all edges. The inner panel shall be 1/2” thick. Both shall be electronically glued hardwood plywood and shall be fastened together with bayonet hanging brackets at the top and two steel angles at the bottom, resulting in a rigid connection with no visible fasteners on the outer wood panel. The veneer face and edges of the outer panel shall be stained to match the architect’s sample. The padding material shall be 2” thick polyurethane foam, shall be glued to the inner panel, and shall conform to the California Bureau of Home Furnishings Technical Bulletin 117. The complete back assembly shall be supported by four 11 gauge formed steel brackets.
D. Armrests: Shall be kiln-dried solid hardwood, nominally 3/4” thick x 2-1/4” wide x 12” long, stained to match the outer back panels. The armrest will be fastened to the steel frame with two #8 x 3/4” pan head sheet metal screws. Chairs equipped with tablet arms shall have armrests nominally 3/4” thick x 2-1/4” wide x
17-1/2” long and shall be attached to the steel frame arm support with three #8 x 3/4” pan head sheet metal screws.
E. Hinge: The seat hinge shall be a weldment consisting of two stamped and formed 14 gauge plates. Hinges shall include two recessed slots to accept 1/4-20 fillister head screws and one pierced, extruded and reamed hole for assembly to the chair frame. Each hinge shall include a rubber bumper to dampen noise upon the seat return to the vertical position. Compensating type hinges will not be acceptable.
PART 3 – OPTIONS
3.1 UPHOLSTERED END PANEL
A. Provide manufacturer’s standard upholstered end panel at the end of the row. The configuration of the panel shall conform to the shape of the end standard frame, shall reside fully within the frame width and shall present fabric surfaces to both the inside and outside of the chair. The end panel assembly shall consist of one inside and one outside panel that are machined of 1/2” thick fiberboard and have all edges eased to insure suitability for upholstery. The outside panel is to contain four 10-24 threaded steel inserts to facilitate assembly to inner panel with four 10-24 x 2” flat head machine screws.
3.2 VENEER END PANEL
A. Provide manufacturer’s standard veneer end panel at the end of the row. The configuration of the panel shall conform to the shape of the end standard frame, shall reside fully within the frame width and shall present finished veneer surfaces to both the inside and outside of the chair. Veneer species and finish to match hardwood armrests. The end panel assembly shall consist of one inside panel machined of 1/2” thick birch plywood and one outside panel machined of 3/4” thick birch plywood. The outside panel is to contain four 10-24 threaded steel inserts to facilitate assembly to the inner panel with four 10-24 x 2” flat head machine screws.
3.3 EXTERNAL END PANEL
A. Provide manufacturer’s standard external veneer end panel at the end of the row. The configuration of the panel shall follow the angle of the frame at the rear, and shall be vertical at the front end. The panel shall be constructed of 3/4” thick plywood with veneer on both sides and 1/8” thick solid wood on the vertical edges. The end panel shall be stained to match the armrests.
3.4 AISLE LIGHT
A. Aisle lights shall be provided in accordance to the locations shown on the architectural drawings. The units shall be of low voltage (24v) type and the light tube shall fit into a routed area on the underside of the armrest. The chair frame shall be prepared to accept the power wire. The necessary access holes and blank cover plates shall be provided. The chair manufacturer shall also provide the necessary transformers. All wiring and electrical connections shall be conducted at the job site and shall be the responsibility of others.
3.5 SEAT AND ROW IDENTIFICATION TAGS
A. Provide manufacturer’s standard shape aluminum number and letter plates. Font shall be Helvetica and the font size shall be 36pt. The number plates shall be attached to the top edge of the seat with spiral shank nails. The row letter plates shall be attached to the top of the armrest with straight shank nails.
3.6 REMOVABLE CHAIR
A. Provide the manufacturer’s standard one, two or three chair removable units which shall include an”

“integrated steel sled-base that is engineered to conform to the row radii and includes two through holes per chair for floor mounting.
3.7 FREESTANDING REMOVABLE CHAIR
A. Provide manufacturer’s standard freestanding removable chair which shall include an integrated steel sled- base that is engineered to conform to the row radii and includes extended length floor plates to allow the chairs to remain stable with no physical attachment to the floor.
3.8 TABLET ARMS
A. Tablet arm shall be two-motion fold-away style, constructed of 1/2” medium density fiberboard, faced two sides with matte black high-pressure laminate. The edges shall be finished with a vinyl T-molding trimmed flush with both top and bottom surfaces.
3.9 POWER/DATA
A. Where indicated on the drawings, chair frames shall be equipped with a 115v/15amp power outlet and a RJ-45 Category 6 data port located on the front of the frame. Wire raceways shall be provided for routing of the wires from chair to chair. All wiring and electrical connections shall be conducted at the job site and shall be the responsibility of others.
3.10 BOOKRACK
A. The bookrack shall be constructed of hardwoods and hardwood plywood. Bookrack shall be assembled with tongue and groove construction and finished with a catalyzed lacquer. The bookrack shall be attached to the outer surface of the chair back. An optional attachment configuration shall consist of a steel weldment attached to the chair leg. This configuration allows the bookrack to be located between chair backs.
3.11 COMPLIANCE WITH CALIFORNIA TECHNICAL BULLETIN 133
PART 4 – WARRANTY
4.1 The theater seating manufacturer must provide a Lifetime Warranty to the original purchaser of the seating as follows:
A. The seating manufacturer shall warrant it’s products against failures and manufacturing defects for the life of the product. This warranty applies to the original purchaser and is non-transferable. The seating manufacturer will provide parts and labor to replace defective parts for the first two years after the installation. Thereafter, the manufacturer will provide replacement parts for the life of theproduct.
B. This warranty shall not cover damage from abuse, misuse, neglect, or act of God. Damage caused by modifications to the product by anyone other than a Navetta authorized seating installation technician will void this warranty. This warranty does not apply to fabrics or products not installed by Navetta authorized seating installation technicians.
PART 5 – EXECUTION
5.1 EXAMINATION
A. Examine site conditions, with installer present, for compliance with requirements for construction tolerances as they affect anchors and fasteners, and location of junction boxes.
B. Do not proceed until unsatisfactory conditions have been corrected.
5.2 GENERAL
A. Comply with seating manufacturer’s printed installation instructions applicable to products.
B. Locate seating in locations indicated on approved shop drawings, with required clearances.
C. Install standards in locations conforming to seating layout, with each standard attached to substrate by no less than two anchoring devices of size and type required to insure that chairs are stable under conditions of actual use.
D. Install chairs using manufacturer’s recommended hardware and fasteners. Insure that chairs in curved rows are installed on proper radius and are oriented toward the center point of the radius. Verify that moving components operate smoothly and quietly.
5.3 ADJUSTING
A. Adjust as required to assure that the seats in each row are aligned when in the uprightposition.”

“B. Touch-up minor abrasions and imperfections in painted finishes with coating that matches factory-applied finish.”
“C. Replace any upholstery that has been damaged during installation.”

Download Acclaim C1 Specs

Download Acclaim C3 Specs

Section 1.01    TECHNICAL  FEATURES

FRAME

1. The seat and the back are made of 10 mm thick natural beech ply-wood, varnished (available in Class 1 fire-retardant) or padded and upholstered (available in Class 1lM fire-retardant version) with the backrest material in polypropylene.
2. The screws are not-unscrewing and the nuts are self-locking.
3. All metal parts are painted with epoxy powders and the small components are protected by a black zinc galvanizing process.

Fixed Seat, on beam

1. The leg is made of oval tubular steel, dimensions 90 x 30 x 2 mm, welded to an oval steel foot 60 x 30 x 1.5 mm with two nylon little feet.
2. The bearing beam is made of 80 x 40 x 2 mm rectangular steel tube.
3. The frame is made of 25 x 1.5 mm tubular steel.

Tip-up seat, on beam

1. The leg is made of elliptical tubular steel, dimensions 76 x 25 x 2 mm, welded to an oval steel foot, dimensions 265 x 90 x 2.5, with two holes for the floor fixing.
2. The bearing beam is made of 80 x 40 x 2 mm rectangular steel tube.
3. The tip-up movement of the seat is mounted on brass bushes and works automatically with a return spring fitted in a polypropylene fulcrum cover.
4. The supports of the seat are made of stamped steel and are 4 mm thick (welded support) or of 3 mm thick (mobile support), whereas the supports for the backrest are in 25 x 1.5 mm tubular steel.

Seating on integral mount for canteen table

1. The leg is in 89×2 mm tubular steel with foot in polypropylene.
2. The supporting cross-pieces are in 60x30x3 rectangular tubing.
3. The rotational movement of the seat is 1800, with a return spring which acts on a ball bearing.
4. The framework is in 25×1.5 mm diameter tubular steel.

PADDING

1. They are made with expanded non-deformable resins.
2. The back is 20 mm thick with a 25 kg/m3 density.
3. The seat is 25 mm thick with a 40 kg/m3 density.

ARMRESTS

1. Fixed chair, swivel chair, or bench with fixed seating The armrests are in black painted steel, 16 mm diameter, the finish on the top is of injection formed polypropylene.

Mobile seating on beam

1. The armrests are in black painted tubular steel, 25×1.5 mm diameter, the finish on the top is made of injection formed polypropylene.

ANTI-PANIC WRITING TABLET

1. The anti-panic writing tablet is made of HPL (High Pressure Laminated) material, 8 mm thick, with rounded edges, black coloured; the anti-panic device is aluminium made with a polypropylene cover.

SMALL FIXED TABLE FOR BENCH

1. Made of 24 mm thick pressed wood, laminate-clad and with rubber edges, both in black; fastened to the beam by a 160×160 mm steel plate and steel omega.

CANTEEN TABLE

1. Made of light grey, water resistant, pressed-wood laminate 29 mm thick, with rounded edges in black PVC, 120 x 80 cm in size.

BOOK BASKET

1. Made of electro-welded steel wire, 6 mm thick.

Section 1.02    WARRANTY

Warranty for specified Navetta Lecture Room Products: Symmetra • Symmetra Plus • Omnia • Monolito

1. Navetta provides the following warranty to the original purchaser of the above listed Navetta products sold in North America and installed by Navetta-approved installers. This warranty begins on the date of product invoice, is governed by and subject to the terms and conditions detailed below, and is non-transferable.
2. Navetta warrants its products to be substantially free from material defects in materials and craftsmanship. Defects found during normal usage of the product will be covered during the warranty period set out below, provided that written notification of the alleged defect is given to Navetta at the address below prior to expiration of the applicable period. Navetta will at its sole discretion either repair or replace the product it determines to be defective with a comparable product. All other costs are excluded.
3. The fulfillment of the warranty is under the control of Navetta. In the event Navetta fails to repair or replace a product it has determined is defective as provided herein, the purchaser’s sole remedy shall be the return of the purchase price actually paid by purchaser for the defective product on a prorated basis based upon a useful life of ten (10) years.

Warranty Period

1. Within ten (10) years of initial shipment: Fixed structural components.
2. Within five (5) years of initial shipment: All other structural components, including seat support arms and pivot mechanisms, springs, tablet arms.
3. Within three (3) years of initial shipment: Plastic components and paint finishes, wood, laminate and other surface finishes (note conditions as to color, grain, and texture set forth below).
4. Within one (1) year of initial shipment: Power and electrical components, seating upholstery including foam (note restrictions as to color, grain, and texture below).

Exclusions and Conditions
This warranty excludes and does not apply to:

1. Conditions other than normal wear and tear.
2. Abuse, neglect, vandalism, or misuse.
3. In-transit damage.
4. Products altered or modified by the purchaser.
5. Products installed on flooring that does not meet structural standards.
6. Purchaser supplied or specified material, leather, and non-standard material and color finishes (whether purchased by the purchaser or Navetta).
7. Natural variations occurring in wood and leather and/or color fastness and/or variations in matching of colors, grains or textures of materials.
8. Product color change due to natural aging, UV exposure, cleaning solutions, or other causes.

Disclaimer of all Other Warranties

1. There are no other warranties than those expressly stated above, whether expressed or implied (including, but not limited to any warranty of merchantability or fitness for any particular purpose). Navetta is not liable for consequential or incidental damage arising from any product defect.

Limitation of Liability

1. Navetta’s total liability hereunder shall not exceed the purchase price paid for the allegedly defective product. In no event shall Navetta be liable for any indirect, consequential, incidental or special damages, including lost profits, loss of reputation, loss of goodwill, lost revenue, or any other economic or non economic loss.

Technical Specifications Fully dismountable armchair with separate elements.

Seat Inner structure in tubular steel 25x25x2, with Pirelli rubber and polypropylene webbing. Seat padding in self-extinguishing polyurethane, cold-foamed, without CFC, complying with UNI 9175, minimum polyurethane density 55 kg/m3, attached to the plywood structure with water based resins glue. Fabric upholstery adheres to the padding without use of glue and is sealed by a zipper.

Backrest inner structure in 13 mm beech ply-wood with side supports in 5 mm thick steel plate.Backrest padding in self-extinguishing contoured polyurethane foam, average thickness of 65 mm and density 40 kg/m3, attached to the plywood structure with water based resins glue. Fabric upholstery adheres to the padding without use of glue. Lower back protector in 1mm thick steel plate.

Side leg in 4mm structural steel with padded side panels; kick plate in 3mm steelplate; side panels in 8mm thick fir chipboard. Side padding in self-extinguishing contoured polyurethane foam, attached to the side panel by water based resins glue. Front and back padding in self-extinguishing contoured polyurethane foam, 65 kg/m3 density attached to the side panel by water based resins glue.

Arm caps: Option 1: padded and upholstered; Option 2: natural varnished solid beechwood Option 3: polyurethane. Seat mechanism: The flip-up mechanism of the seat works by gravity. The floor fixing bracket is in steel 4 mm. thick. The kick plate is in grey varnished steel plate or in varnished solid beechwood. All visible metal parts are in grey color, painted with epoxy scratch-resistant powders. The armchair has the Italian Class 1IM Certificate for flame retardancy from the Italian Ministry of the Interior.

WRITING TABLET Genesis Evolution can be equipped with a flip up writing tablet inside the armrest, in High Pressure Laminated (HPL), overall dimensions (226 x 310 x 8 mm), with rounded edges, black colour; the anti-panic mechanism of the tablet is in steel. As an alternative an antipanic table fixed on the back, scratch-resistant bilaminate wood conglomerate with squared front edge ( no bull nosed) Side and back edges in ABS, 2 mm thick; standard depth 300 mm, standard thickness 30 mm.

The table brackets are in 3 mm thick stamped steel. Its movement is obtained by using two stamped steel hinges which are 5 mm. thick and rotate on brass bushes.

ACCESSORIES: -Embroidered and row numbering, -Row terminal light.

Section 1.01    SUMMARY

1. Table systems
2. Fixed Table: Monolito System
3. Extent: Systems to be as indicated on drawings and as specified

Section 1.02    PRODUCT DESCRIPTION

1. Seat/Table Requirements:
2. Pedestal: provide table and supports providing fixed work surface with open access, supported by pedestals.
3. Power and Data Distribution System: Modular data and electrical system housed in flexible conduit. All current-carrying power system components shall be UL approved, and will have appropriate labeling documenting that approval.

Section 1.03    SUBMITTALS

1. General: Submit listed submittals in accordance with Contract and standard Submittals Procedures.
2. Product Data: Submit manufacturers’ product data, including product specification sheets, for products specified.
3. Shop Drawings: Submit shop drawings showing seating layout, seat-numbering scheme, chair sizes and aisle widths.
4. Samples: Submit verification samples of finishes, colors and textures specified for each exposed material.
5. Quality Assurance Submittals; Submit the following:
   • Certificates: Product certificates signed by manufacturer certifying materials comply with specify performance characteristics and criteria and physical requirements.
   • Installer Qualifications: Submit certification indicating installer is qualified to install manufacturer’s seating.
   • Bidder Qualifications: Submit certification, prior to drawing completion, indicating site has been inspected for any conditions that may affect the assembly or installation of products required.

Section 1.04    WARRANTY

Warranty for specified Navetta Lecture Room Products: Symmetra • Symmetra Plus • Omnia • Monolito

1. 1. Navetta provides the following warranty to the original purchaser of the above listed Navetta products sold in North America and installed by Navetta-approved installers. This warranty begins on the date of product invoice, is governed by and subject to the terms and conditions detailed below, and is non-transferable.
   2. Navetta warrants its products to be substantially free from material defects in materials and craftsmanship. Defects found during normal usage of the product will be covered during the warranty period set out below, provided that written notification of the alleged defect is given to Navetta at the address below prior to expiration of the applicable period. Navetta will at its sole discretion either repair or replace the product it determines to be defective with a comparable product. All other costs are excluded.
   3. The fulfillment of the warranty is under the control of Navetta. In the event Navetta fails to repair or replace a product it has determined is defective as provided herein, the purchaser’s sole remedy shall be the return of the purchase price actually paid by purchaser for the defective product on a prorated basis based upon a useful life of ten (10) years.

   Warranty Period

   1. Within ten (10) years of initial shipment: Fixed structural components.
   2. Within five (5) years of initial shipment: All other structural components, including seat support arms and pivot mechanisms, springs, tablet arms.
   3. Within three (3) years of initial shipment: Plastic components and paint finishes, wood, laminate and other surface finishes (note conditions as to color, grain, and texture set forth below).
   4. Within one (1) year of initial shipment: Power and electrical components, seating upholstery including foam (note restrictions as to color, grain, and texture below).

   Exclusions and Conditions
   This warranty excludes and does not apply to:

   1. Conditions other than normal wear and tear.
   2. Abuse, neglect, vandalism, or misuse.
   3. In-transit damage.
   4. Products altered or modified by the purchaser.
   5. Products installed on flooring that does not meet structural standards.
   6. Purchaser supplied or specified material, leather, and non-standard material and color finishes (whether purchased by the purchaser or Navetta).
   7. Natural variations occurring in wood and leather and/or color fastness and/or variations in matching of colors, grains or textures of materials.
   8. Product color change due to natural aging, UV exposure, cleaning solutions, or other causes.

   Disclaimer of all Other Warranties

   1. There are no other warranties than those expressly stated above, whether expressed or implied (including, but not limited to any warranty of merchantability or fitness for any particular purpose). Navetta is not liable for consequential or incidental damage arising from any product defect.

   Limitation of Liability

   1. Navetta’s total liability hereunder shall not exceed the purchase price paid for the allegedly defective product. In no event shall Navetta be liable for any indirect, consequential, incidental or special damages, including lost profits, loss of reputation, loss of goodwill, lost revenue, or any other economic or non economic loss.

   Warranty Notice Address

   Navetta division of Shuttlesystem
   11340 Montgomery Road, Ste 200
   Mason OH 45040
   513-489-3727

Section 2.01    TABLE SYSTEM

1. Manufacturer: Navetta division of Shuttlesystem LLC
2. Product: Monolito Fixed Table System
3. Product specifications
4. Pedestal Support – Construction: Pedestals shall be constructed of paired extruded structural aluminum columns measuring 2.3” x 2.2”, with heavy-duty .09” wall thickness and internal reinforcing ribs measuring .20” thickness.
5. Floor mount – Pedestal shall be rigidly mounted to a .25” thick steel base plate measuring 11.5” x 2.5” with four holes for mounting pedestal to floor with anchor bolts.
6. Pedestal Support Side Covers – Floor mounting hardware and top mounting hardware to be fully concealed by two 7.0” wide aluminum extruded removable panels.
7. Table mount – Top mount bracket shall be constructed of .25” thick steel plate with eight attaching screws allowing attachment to pedestal columns. Bracket shall provide four mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
8. Metal Finish – Steel brackets shall have powder-coat finish, aluminum pedestal columns and covers will have anodized finish.
9. Table Configuration – Table tops shall be designed to be assembled into continuous surface in straight, radius, or segmented configuration. Adjacent tops to be joined with two mechanical clamping fasteners. Tops shall have cutouts for tabletop power modules when specified. Manufacturer shall be FSC (Forest Stewardship Council) chain-of-custody Certified.
10. Table Top Construction – Table tops shall be nominal 1.25” thick warp-resistant construction with 1.125” particleboard center core sandwiched between .040” high pressure laminate top surface and phenolic backing surface. Assembly to be permanently bonded under continuous pressure in hot press.
11. Table Top Edge treatment – Edges shall be finished as specified, using 3mm PVC, “T” cross-section vinyl continuous molding, wood surface, or bonded resin edging.
12. Table Top Attachment – Table tops to attach to pedestal brackets with four #14 lag screws.
13. Modesty Panel Construction – Modesty panels shall be constructed of .8” thick nominal particle board sandwiched with bonded high-pressure laminate as specified and phenolic backing sheet, or available perforated metal of specified material, pattern and finish.
14. Modesty Panel Attachment – Modesty panels shall interlock into machined recess in underside of table top surface and attach with supplied rigid metal brackets and hardware. Standard configuration positions modesty panels between pedestal supports.

Section 3.1      MANUFACTURER’S INSTRUCTIONS

1. Comply with manufacturer’s installation instructions, including bulletins, product catalog, installation instructions and product carton instructions for installation.

Section 3.2      EXAMINATION

1. Site Verification: Prior to installation verify, with installer present, that substrates and conditions comply with the requirements for construction tolerances and materials properties as they affect anchors and fasteners and location of junction boxes.
2. Repair: Do not proceed until unsatisfactory components or facility conditions have been corrected.

Section 3.3      INSTALLATION

1. Installation: Install following manufacturers printed instructions for installation and using manufacturer recommended hardware and fasteners. Tables in curbed rows shall be installed at smooth radius.
2. Repair: Repair minor abrasions and imperfections in painted surfaces with a coating that matches the factory- applied finish.

Section 3.4      CLEANING AND PROTECTION

1. Cleaning: Clean Product in accordance with manufacturer instruction prior to Owner’s acceptance. Remove construction debris, including cartons from project site and legally dispose of debris.
2. Protection: Protect installed product and finished surfaces from damage during construction.

Section 1.01    SUMMARY

1. Table systems
2. Fixed Table: Symmetra System
3. Extent: Systems to be as indicated on drawings and as specified

Section 1.02    PRODUCT DESCRIPTION

1. Seat/Table Requirements:
2. Pedestal: provide table and supports providing fixed work surface with open access, supported by pedestals.
3. Power and Data Distribution System: Modular data and electrical system housed in flexible conduit. All power system components shall be UL approved, including the steel pedestal table leg used for power entry, which shall be certified as a “UL Recognized Component,” and will have appropriate labeling documenting that approval.

Section 1.03    SUBMITTALS

1. General: Submit listed submittals in accordance with Contract and standard Submittals Procedures.
2. Product Data: Submit manufacturers’ product data, including product specification sheets, for products specified.
3. Shop Drawings: Submit shop drawings showing seating layout, seat-numbering scheme, chair sizes and aisle widths.
4. Samples: Submit verification samples of finishes, colors and textures specified for each exposed material.
5. Quality Assurance Submittals; Submit the following:
6. Certificates: Product certificates signed by manufacturer certifying materials comply with specify performance characteristics and criteria and physical requirements.
7. Installer Qualifications: Submit certification indicating installer is qualified to install manufacturer’s seating.
8. Bidder Qualifications: Submit certification, prior to drawing completion, indicating site has been inspected for any conditions that may affect the assembly or installation of products required.

Section 1.04    WARRANTY
Warranty for specified Navetta Lecture Room Products: Symmetra • Symmetra Plus • Omnia • Monolito

1. 1. Navetta provides the following warranty to the original purchaser of the above listed Navetta products sold in North America and installed by Navetta-approved installers. This warranty begins on the date of product invoice, is governed by and subject to the terms and conditions detailed below, and is non-transferable.
   2. Navetta warrants its products to be substantially free from material defects in materials and craftsmanship. Defects found during normal usage of the product will be covered during the warranty period set out below, provided that written notification of the alleged defect is given to Navetta at the address below prior to expiration of the applicable period. Navetta will at its sole discretion either repair or replace the product it determines to be defective with a comparable product. All other costs are excluded.
   3. The fulfillment of the warranty is under the control of Navetta. In the event Navetta fails to repair or replace a product it has determined is defective as provided herein, the purchaser’s sole remedy shall be the return of the purchase price actually paid by purchaser for the defective product on a prorated basis based upon a useful life of ten (10) years.

   Warranty Period

   1. Within ten (10) years of initial shipment: Fixed structural components.
   2. Within five (5) years of initial shipment: All other structural components, including seat support arms and pivot mechanisms, springs, tablet arms.
   3. Within three (3) years of initial shipment: Plastic components and paint finishes, wood, laminate and other surface finishes (note conditions as to color, grain, and texture set forth below).
   4. Within one (1) year of initial shipment: Power and electrical components, seating upholstery including foam (note restrictions as to color, grain, and texture below).

   Exclusions and Conditions
   This warranty excludes and does not apply to:

   1. Conditions other than normal wear and tear.
   2. Abuse, neglect, vandalism, or misuse.
   3. In-transit damage.
   4. Products altered or modified by the purchaser.
   5. Products installed on flooring that does not meet structural standards.
   6. Purchaser supplied or specified material, leather, and non-standard material and color finishes (whether purchased by the purchaser or Navetta).
   7. Natural variations occurring in wood and leather and/or color fastness and/or variations in matching of colors, grains or textures of materials.
   8. Product color change due to natural aging, UV exposure, cleaning solutions, or other causes.

   Disclaimer of all Other Warranties

   1. There are no other warranties than those expressly stated above, whether expressed or implied (including, but not limited to any warranty of merchantability or fitness for any particular purpose). Navetta is not liable for consequential or incidental damage arising from any product defect.

   Limitation of Liability

   1. Navetta’s total liability hereunder shall not exceed the purchase price paid for the allegedly defective product. In no event shall Navetta be liable for any indirect, consequential, incidental or special damages, including lost profits, loss of reputation, loss of goodwill, lost revenue, or any other economic or non economic loss.

   Warranty Notice Address

2. Navetta division of ShuttleSystem
   11340 Montgomery Rd,Suite 200
   Mason, OH 45040
   513-489-3727

Section 2.01    TABLE SYSTEM

1. Manufacturer: Navetta division of Shuttlesystem LLC
2. Product: Symmetra Fixed Table System
3. Product specifications
4. Pedestal Support – Construction: Pedestals shall be constructed of 11 gauge steel tubing of oval cross-section measuring 3.15” x 1.57”.
5. Floor mount – Pedestal shall be computer-controlled welded to a .25” thick steel base plate measuring 8” x 4” with four slotted holes for mounting pedestal to floor with anchor bolts.
6. Base cover – Base plate to be fully covered after mounting with two-piece cover constructed of injection molded toughened nylon, attached with two machine screws.
7. Table mount – Top mount bracket shall be constructed of 11 gauge steel with four attaching bolts allowing attachment to pedestal and adjustment for variations in floor surface to provide alignment of adjacent tabletops without shimming tops. Bracket shall provide six mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
8. Top shroud – Top mount bracket will be covered by shroud with rounded edges constructed of injection molded ABS, attached with machine screws.
9. Metal Finish – Metal components shall have powder-coat finish in finish specified.
10. Table Configuration – Table tops shall be designed to be assembled into continuous surface in straight, radius, or segmented configuration. Adjacent tops to be joined with two mechanical clamping fasteners. Tops shall have cutouts for tabletop power modules when specified. Manufacturer shall be FSC (Forest Stewardship Council) chain-of-custody Certified.
11. Table Top Construction – Table tops shall be nominal 1.25” thick warp-resistant construction with 1.125” particleboard center core sandwiched between .040” high pressure laminate top surface and phenolic backing surface. Assembly to be permanently bonded under continuous pressure in hot press.
12. Table Top Edge treatment – Edges shall be finished as specified, using 3mm PVC, “T” cross-section vinyl continuous molding, wood surface, or bonded resin edging.
13. Table Top Attachment – Table tops to attach to pedestal brackets with six #12 lag bolts.
14. Modesty Panel Construction – Modesty panels shall be constructed of .8” thick nominal particle board sandwiched with bonded high-pressure laminate as specified and phenolic backing sheet, or available perforated metal of specified material, pattern and finish.
15. Modesty Panel Attachment – Modesty panels shall interlock into machined recess in underside of table top surface and attach with supplied rigid metal brackets and hardware. Standard configuration provides .5” clearance between adjacent modesty panels, continuous configuration optional.
16. End Panel Construction – If specified, end panels shall be constructed of .8” thick nominal particle board sandwiched with bonded high-pressure laminate as specified and phenolic backing sheet, or available perforated metal of specified material, pattern and finish.
17. End Panel Attachment – End Panels shall attach with supplied rigid metal brackets and hardware.

Section 3.1      MANUFACTURER’S INSTRUCTIONS

1. Comply with manufacturer’s installation instructions, including bulletins, product catalog, installation instructions and product carton instructions for installation.

Section 3.2      EXAMINATION

1. Site Verification: Prior to installation verify, with installer present, that substrates and conditions comply with the requirements for construction tolerances and materials properties as they affect anchors and fasteners and location of junction boxes.
2. Repair: Do not proceed until unsatisfactory components or facility conditions have been corrected.

Section 3.3      INSTALLATION

1. Installation: Install following manufacturers printed instructions for installation and using manufacturer recommended hardware and fasteners. Tables in curbed rows shall be installed at smooth radius.
2. Repair: Repair minor abrasions and imperfections in painted surfaces with a coating that matches the factory- applied finish.

Section 3.4      CLEANING AND PROTECTION

1. Cleaning: Clean Product in accordance with manufacturer instruction prior to Owner’s acceptance. Remove construction debris, including cartons from project site and legally dispose of debris.
2. Protection: Protect installed product and finished surfaces from damage during construction.

Technical features

Backrest Inner structure in beech plywood, 15 mm thick; Padding in non-deformable, self extinguishing polyurethane foam with variable density, complying with UNI norm 9175, density of 30 kg Kg/m3, attached to the wood structure by means of adhesive waterbased resins. Upholstery made in fabric not directly glued to the padding.

Back

mechanism kit with gas cylinder Side leg fixing plate in laser-cut steel plate, 5 mm thick Side legs connection plate in laser-cut and folded steel plate, 5mm thick; Supports of the backrest mechanism in laser-cut steel plate, pressed and folded, 5mm thick, with self-lubricating bushings. 200 Newton gas cylinder with quick fixing system.

Seat

Structure in beech plywood, 15 mm thick with side supports in pressed steel plate, 3mm thick, and 15mm steel rod. Padding in non-deformable, self extinguishing polyurethane foam with variable density, complying with UNI norm 9175, density of 40 kg Kg/m3, attached to the wood structure by means of adhesive water-based resins Counterweight in 30x6mm laminated steel. Upholstery made in fabric not directly glued to the padding.

Side

leg Structure in 4mm steel plate; kickplate in 10mm thick pressed steel plate with 2 floor fixing points. Side and lower panels in fir chipboard, 8mm thick Side padding in non-deformable, self extinguishing polyurethane foam with variable density, complying with UNI norm 9175, density of 40 kg Kg/m3, attached to the wood structure by means of adhesive water-based resins. Front and back padding in non-deformable, self extinguishing polyurethane foam with variable density, complying with UNI norm 9175, density of 65 kg Kg/m3, attached to the closing panels by means of adhesive water-based resins. Armrest padding in non-deformable, self extinguishing polyurethane foam with variable density, complying with UNI norm 9175, density of 65 kg Kg/m3, attached to the closing panels by means of adhesive water-based resins. Seat rotation mechanism in polypropylene.

Accessories

Seat and row numbering thermo glued or embroidered. Custom colors for the metal structure are available Screws for fixing on a R35 concrete floor Flip-up antipanic writing tablet in the side leg, rounded edges, in black HPL, 8 mm. Supports in steel plate, 2,5 mm thick and steel rod of 12mm. Mobile hinges in brass.

Section 1.01    SUMMARY

1. Auditorium Seating
2. Fixed Auditorium Seating with Tablet Arm
3. Extent: Seating to be as indicated on drawings and as specified

Section 1.02    PRODUCT DESCRIPTION

1. Seat Requirements:
2. Chair: provide and install fixed auditorium seating with uplift seat bottom and optional anti-panic tablet arm per drawing.
3. Dimensions are nominal and based on current product information.

Section 1.03    SUBMITTALS

1. General: Submit listed submittals in accordance with Contract and standard Submittals Procedures.
2. Product Data: Submit manufacturers’ product data, including product specification sheets, for products specified.
3. Shop Drawings: Submit shop drawings showing seating layout, seat-numbering scheme, chair sizes and aisle widths.
4. Samples: Submit verification samples of finishes, colors and textures specified for each exposed material.
5. Quality Assurance Submittals; Submit the following:
6. Certificates: Product certificates signed by manufacturer certifying materials comply with specify performance characteristics and criteria and physical requirements.
7. Installer Qualifications: Submit certification indicating installer is qualified to install manufacturer’s seating.
8. Bidder Qualifications: Submit certification, prior to drawing completion, indicating site has been inspected for any conditions that may affect the assembly or installation of products required.

Section 1.04    WARRANTY

1. Project Warranty: Refer to “Conditions of the Contract” to project warranty provisions.
2. Manufacturer’s Warranty: Submit, for Owners acceptance:
3. Manufacturer’s standard warranty documents executed by authorized company official. Manufacturer’s warranty is in addition to, and not a limitation of, other rights Owners may have under Contract Documents.
4. Warranty period; Seven (7) year warranty on mechanical and steel structure from defects of manufacture and workmanship, commencing on Date of Substantial Completion.
5. Warranty will be null and void if products are installed on flooring not meeting minimum structural requirements as specified by manufacturer.

Section 2.01    SEATING/TABLET SYSTEM

1. Manufacturer: Navetta division of Shuttlesystem LLC
2. Product: Eidos Auditorium Seat
3. Product specifications
4. Seat – Fully upholstered seat with 2.75” average thickness 2.5 lb/cu. ft. HR density self-extinguishing polyurethane foam provides maximum comfort and durability. Gravity uplift seat with counterweight mechanism automatically returns the seat to its vertical position when unoccupied. Optional California Bulletin 133 compliance. Center to center seat sizes in 20.5”, 21.75”, 22.75”, 24.5”, 26.75”.
5. Back – Fully upholstered upper back outer panel. Lower panel also available in polypropylene and wood. Inner panel is made of 0.4” thick birch plywood, upholstered with 2.75” average thickness 1.9 lb/cu. ft. density HR polyurethane foam with double curved ergonomic design for comfort / lumbar support. Back height is available in 36.2”, 38.2” and 44”. Center to center back sizes in 20.5”, 21.75”, 22.75”, 24.5”, 26.75”.
6. Side/Arms – Side panels available with fabric upholstery. Armrest structure is powder coated .160” steel. Armrest available upholstered with .8” thickness 3.75 lb/cu. ft. density foam padding, contoured injection molded ABS, or natural varnished wood.
7. Pedestal Supports – Formed oval steel tubing measuring 3.5” x 1.2” cross section, welded to .100” thick mounting flange. Epoxy powder coat finish.
8. Tablet Arm – Contoured phenolic tablet arm 13.75”wide and 10” deep. Machined swivel joint with mechanism tested to support 500 lbs. The tablet arm opens and stows in one movement for antipanic egress.
9. Options – Power provision, Aisle light with illuminated row letter and seat numbers, embroidered seat numbering, riser mounted standards, removable base, wood seat bottom and back panel.

Section 3.1      MANUFACTURER’S INSTRUCTIONS

1. Comply with manufacturer’s installation instructions, including bulletins, product catalog, installation instructions and product carton instructions for installation.

Section 3.2      EXAMINATION

1. Site Verification: Prior to installation verify, with installer present, that substrates and conditions comply with the requirements for construction tolerances and materials properties as they affect anchors and fasteners and location of junction boxes.
2. Repair: Do not proceed until unsatisfactory components or facility conditions have been corrected.

Section 3.3      INSTALLATION

1. Installation: Install following manufacturers printed instructions for installation and using manufacturer recommended hardware and fasteners. Tables in curved rows shall be installed at smooth radius.
2. Repair: Repair minor abrasions and imperfections in painted surfaces with a coating that matches the factory- applied finish.
3. Replace: Replace any fabric damaged during installation.

Section 3.4      CLEANING AND PROTECTION

1. Cleaning: Clean Product in accordance with manufacturer instruction prior to Owner’s acceptance. Remove construction debris, including cartons from project site and legally dispose of debris.
2. Protection: Protect installed product and finished surfaces from damage during construction.

Section 1.01    SUMMARY

1. Table systems with swingout seating
2. Fixed Table System with swingout seating: Symmetra Plus System
3. Extent: Systems to be as indicated on drawings and as specified

Section 1.02    PRODUCT DESCRIPTION

1. Seat/Table Requirements:
2. Pedestal: provide table and supports providing fixed work surface with open access, supported by pedestals.
3. Seating: Provide modular seating supported by swing arms on either side of each support pedestal, seats to independently swing out for access and swing back adjacent to table top when unoccupied.
4. Power and Data Distribution System: Modular data and electrical system housed in flexible conduit. All power system components shall be UL approved, including the steel pedestal table leg used for power entry, which shall be certified as a “UL Recognized Component,” and will have appropriate labeling documenting that approval.

Section 1.03    SUBMITTALS

1. General: Submit listed submittals in accordance with Contract and standard Submittals Procedures.
2. Product Data: Submit manufacturers’ product data, including product specification sheets, for products specified.
3. Shop Drawings: Submit shop drawings showing seating layout, seat-numbering scheme, chair sizes and aisle widths.
4. Samples: Submit verification samples of finishes, colors and textures specified for each exposed material.
5. Quality Assurance Submittals; Submit the following:
6. Certificates: Product certificates signed by manufacturer certifying materials comply with specify performance characteristics and criteria and physical requirements.
7. Installer Qualifications: Submit certification indicating installer is qualified to install manufacturer’s seating.
8. Bidder Qualifications: Submit certification, prior to drawing completion, indicating site has been inspected for any conditions that may affect the assembly or installation of products required.

Section 1.04    WARRANTY

1. Project Warranty: Refer to “Conditions of the Contract” to project warranty provisions.
2. Manufacturer’s Warranty: Submit, for Owners acceptance:
3. Manufacturer’s standard warranty documents executed by authorized company official. Manufacturer’s warranty is in addition to, and not a limitation of, other rights Owners may have under Contract Documents.
4. Warranty period; Ten (10) year warranty on understructure and seating shells (when utilized) from defects of manufacture and workmanship, commencing on Date of Substantial Completion.
5. Warranty will be null and void if products are installed on flooring not meeting minimum structural requirements as specified by manufacturer.

Section 2.01    TABLE SYSTEM

1. Manufacturer: Navetta division of Shuttlesystem LLC
2. Product: Symmetra Fixed Table System
3. Product specifications
4. Inner Pedestal Support – Construction: Pedestals shall be constructed of 11 gauge steel tubing of oval cross-section measuring 3.15” x 1.57”.
5. Inner Pedestal Support Floor mount – Pedestal shall be computer-controlled welded to a .25” thick steel base plate measuring 8” x 4” with four slotted holes for mounting pedestal to floor with anchor bolts.
6. Inner Pedestal Support Base cover – Base plate to be fully covered after mounting with two-piece cover constructed of injection molded toughened nylon, attached with two machine screws.
7. Inner Pedestal Support Table mount – Top mount bracket shall be constructed of 11 gauge steel with four attaching bolts allowing attachment to pedestal and adjustment for variations in floor surface to provide alignment of adjacent tabletops without shimming tops. Bracket shall provide six mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
8. Inner Pedestal Support Top shroud – Top mount bracket will be covered by shroud with rounded edges constructed of vacuum formed ABS, attached with screws.
9. Outer Pedestal Support – Construction: Pedestals shall be constructed of paired extruded structural aluminum columns measuring 2.3” x 2.2”, with heavy-duty .09” wall thickness and internal reinforcing ribs measuring .20” thickness.
10. Outer Pedestal Support Floor mount – Pedestal shall be rigidly mounted to a .25” thick steel base plate measuring 11.5” x 2.5” with four holes for mounting pedestal to floor with anchor bolts.
11. Outer Pedestal Support Side Cover – Floor mounting hardware and top mounting hardware to be fully concealed by two 7.0” wide aluminum extruded removable panels.
12. Outer Pedestal Support Table mount – Top mount bracket shall be constructed of .25” thick steel plate with eight attaching screws allowing attachment to pedestal columns. Bracket shall provide four mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
13. Metal Finish – Steel components shall have powder-coat finish in finish specified. Aluminum components shall have anodized finish or powder-coat finish in finish specified.
14. Table Configuration – Table tops shall be designed to be assembled into continuous surface in straight, radius, or segmented configuration. Adjacent tops to be joined with two mechanical clamping fasteners. Tops shall have cutouts for tabletop power modules when specified. Manufacturer shall be FSC (Forest Stewardship Council) chain-of-custody Certified.
15. Table Top Construction – Table tops shall be nominal 1.25” thick warp-resistant construction with 1.125” particleboard center core sandwiched between .040” high pressure laminate top surface and phenolic backing surface. Assembly to be permanently bonded under continuous pressure in hot press.
16. Table Top Edge treatment – Edges shall be finished as specified, using 3mm PVC, “T” cross-section vinyl continuous molding, wood surface, or bonded resin edging.
17. Inner Pedestal Support Table Top Attachment – Table tops to attach to pedestal brackets with six #12 lag screws.
18. Outer Pedestal Support Table Top Attachment – Table tops to attach to pedestal brackets with 4 #14 lag screws.
19. Modesty Panel Construction – Modesty panels shall be constructed of .8” thick nominal particle board sandwiched with bonded high-pressure laminate as specified and phenolic backing sheet, or available perforated metal of specified material, pattern and finish.
20. Modesty Panel Attachment – Modesty panels shall interlock into machined recess in underside of table top surface and attach with supplied rigid metal brackets and hardware. Standard configuration provides .5” clearance between adjacent modesty panels, continuous configuration optional.
21. Seat Support Mechanism – Seat support arms shall be constructed of 11 gauge oval steel tubing formed to a radius, with industry-standard taper receiver to accept chair cylinder. Arms on either side of the support pedestal shall pivot independently from a steel kingpin mounted in a die cast aluminum housing with powder coat finish. A field-adjustable torsion spring shall be implemented to automatically return the seat adjacent to the table top when not occupied.
22. Seat Specifications – A large selection of standard seats are available with the Symmetra Plus system, and virtually any other seat can be used with the system, including plastic, mesh back, and wood construction, upholstered or not, as the customer prefers. See specified seat documentation for detailed specification.

Section 3.1      MANUFACTURER’S INSTRUCTIONS

1. Comply with manufacturer’s installation instructions, including bulletins, product catalog, installation instructions and product carton instructions for installation.

Section 3.2      EXAMINATION

1. Site Verification: Prior to installation verify, with installer present, that substrates and conditions comply with the requirements for construction tolerances and materials properties as they affect anchors and fasteners and location of junction boxes.
2. Repair: Do not proceed until unsatisfactory components or facility conditions have been corrected.

Section 3.3      INSTALLATION

1. Installation: Install following manufacturers printed instructions for installation and using manufacturer recommended hardware and fasteners. Tables in curbed rows shall be installed at smooth radius.
2. Repair: Repair minor abrasions and imperfections in painted surfaces with a coating that matches the factory- applied finish.

Section 3.4      CLEANING AND PROTECTION

1. Cleaning: Clean Product in accordance with manufacturer instruction prior to Owner’s acceptance. Remove construction debris, including cartons from project site and legally dispose of debris.
2. Protection: Protect installed product and finished surfaces from damage during construction.

Section 1.01    SUMMARY

1. Table systems
2. Fixed Table: Symmetra System
3. Extent: Systems to be as indicated on drawings and as specified

Section 1.02    PRODUCT DESCRIPTION

1. Seat/Table Requirements:
2. Pedestal: provide table and supports providing fixed work surface with open access, supported by pedestals.
3. Power and Data Distribution System: Modular data and electrical system housed in flexible conduit. All power system components shall be UL approved, including the steel pedestal table leg used for power entry, which shall be certified as a “UL Recognized Component,” and will have appropriate labeling documenting that approval.

Section 1.03    SUBMITTALS

1. General: Submit listed submittals in accordance with Contract and standard Submittals Procedures.
2. Product Data: Submit manufacturers’ product data, including product specification sheets, for products specified.
3. Shop Drawings: Submit shop drawings showing seating layout, seat-numbering scheme, chair sizes and aisle widths.
4. Samples: Submit verification samples of finishes, colors and textures specified for each exposed material.
5. Quality Assurance Submittals; Submit the following:
   • Certificates: Product certificates signed by manufacturer certifying materials comply with specify performance characteristics and criteria and physical requirements.
   • Installer Qualifications: Submit certification indicating installer is qualified to install manufacturer’s seating.
   • Bidder Qualifications: Submit certification, prior to drawing completion, indicating site has been inspected for any conditions that may affect the assembly or installation of products required.

Section 1.04    WARRANTY

1. Project Warranty: Refer to “Conditions of the Contract” to project warranty provisions.
2. Manufacturer’s Warranty: Submit, for Owners acceptance:
3. Manufacturer’s standard warranty documents executed by authorized company official. Manufacturer’s warranty is in addition to, and not a limitation of, other rights Owners may have under Contract Documents.
4. Warranty period; Ten (10) year warranty on understructure and seating shells (when utilized) from defects of manufacture and workmanship, commencing on Date of Substantial Completion.
5. Warranty will be null and void if products are installed on flooring not meeting minimum structural requirements as specified by manufacturer.

Section 2.01    TABLE SYSTEM

1. Manufacturer: Navetta division of Shuttlesystem LLC
2. Product: Symmetra Fixed Table System
3. Product specifications
4. Inner Pedestal Support – Construction: Pedestals shall be constructed of 11 gauge steel tubing of oval cross-section measuring 3.15” x 1.57”.
5. Inner Pedestal Support Floor mount – Pedestal shall be computer-controlled welded to a .25” thick steel base plate measuring 8” x 4” with four slotted holes for mounting pedestal to floor with anchor bolts.
6. Inner Pedestal Support Base cover – Base plate to be fully covered after mounting with two-piece cover constructed of injection molded toughened nylon, attached with two machine screws.
7. Inner Pedestal Support Table mount – Top mount bracket shall be constructed of 11 gauge steel with four attaching bolts allowing attachment to pedestal and adjustment for variations in floor surface to provide alignment of adjacent tabletops without shimming tops. Bracket shall provide six mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
8. Inner Pedestal Support Top shroud – Top mount bracket will be covered by shroud with rounded edges constructed of injection molded ABS, attached with machine screws.
9. Outer Pedestal Support – Construction: Pedestals shall be constructed of paired extruded structural aluminum columns measuring 2.3” x 2.2”, with heavy-duty .09” wall thickness and internal reinforcing ribs measuring .20” thickness.
10. Outer Pedestal Support Floor mount – Pedestal shall be rigidly mounted to a .25” thick steel base plate measuring 11.5” x 2.5” with four holes for mounting pedestal to floor with anchor bolts.
11. Outer Pedestal Support Side Cover – Floor mounting hardware and top mounting hardware to be fully concealed by two 7.0” wide aluminum extruded removable panels.
12. Outer Pedestal Support Table mount – Top mount bracket shall be constructed of .25” thick steel plate with eight attaching screws allowing attachment to pedestal columns. Bracket shall provide four mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
13. Metal Finish – Steel components shall have powder-coat finish in finish specified. Aluminum components shall have anodized finish or powder-coat finish in finish specified.
14. Table Configuration – Table tops shall be designed to be assembled into continuous surface in straight, radius, or segmented configuration. Adjacent tops to be joined with two mechanical clamping fasteners. Tops shall have cutouts for tabletop power modules when specified. Manufacturer shall be FSC (Forest Stewardship Council) chain-of-custody Certified.
15. Table Top Construction – Table tops shall be nominal 1.25” thick warp-resistant construction with 1.125” particleboard center core sandwiched between .040” high pressure laminate top surface and phenolic backing surface. Assembly to be permanently bonded under continuous pressure in hot press.
16. Table Top Edge treatment – Edges shall be finished as specified, using 3mm PVC, “T” cross-section vinyl continuous molding, wood surface, or bonded resin edging.
17. Inner Pedestal Support Table Top Attachment – Table tops to attach to pedestal brackets with six #12 lag screws.
18. Outer Pedestal Support Table Top Attachment – Table tops to attach to pedestal brackets with 4 #14 lag screws.
19. Modesty Panel Construction – Modesty panels shall be constructed of .8” thick nominal particle board sandwiched with bonded high-pressure laminate as specified and phenolic backing sheet, or available perforated metal of specified material, pattern and finish.
20. Modesty Panel Attachment – Modesty panels shall interlock into machined recess in underside of table top surface and attach with supplied rigid metal brackets and hardware. Standard configuration provides .5” clearance between adjacent modesty panels, continuous configuration optional.

Section 3.1      MANUFACTURER’S INSTRUCTIONS

1. Comply with manufacturer’s installation instructions, including bulletins, product catalog, installation instructions and product carton instructions for installation.

Section 3.2      EXAMINATION

1. Site Verification: Prior to installation verify, with installer present, that substrates and conditions comply with the requirements for construction tolerances and materials properties as they affect anchors and fasteners and location of junction boxes.
2. Repair: Do not proceed until unsatisfactory components or facility conditions have been corrected.

Section 3.3      INSTALLATION

1. Installation: Install following manufacturers printed instructions for installation and using manufacturer recommended hardware and fasteners. Tables in curbed rows shall be installed at smooth radius.
2. Repair: Repair minor abrasions and imperfections in painted surfaces with a coating that matches the factory- applied finish.

Section 3.4      CLEANING AND PROTECTION

1. Cleaning: Clean Product in accordance with manufacturer instruction prior to Owner’s acceptance. Remove construction debris, including cartons from project site and legally dispose of debris.
2. Protection: Protect installed product and finished surfaces from damage during construction.

Section 1.01    SUMMARY

1. Table systems with swingout seating
2. Fixed Table System with swingout seating: Symmetra Plus System
3. Extent: Systems to be as indicated on drawings and as specified

Section 1.02    PRODUCT DESCRIPTION

1. Seat/Table Requirements:
2. Pedestal: provide table and supports providing fixed work surface with open access, supported by pedestals.
3. Seating: Provide modular seating supported by swing arms on either side of each support pedestal, seats to independently swing out for access and swing back adjacent to table top when unoccupied. Auto-height auto-return seat cylinder allowing seat height adjustment, chair rotation and center return. Height adjustment mechanism and cylinder utilize precision taper fit, which eliminates requirement of tools and set screws. All seats must spin 360 degrees with standard spacing.
4. Power and Data Distribution System: Modular data and electrical system housed in flexible conduit. All power system components shall be UL approved, including the steel pedestal table leg used for power entry, which shall be certified as a “UL Recognized Component,” and will have appropriate labeling documenting that approval.

Section 1.03    SUBMITTALS

1. General: Submit listed submittals in accordance with Contract and standard Submittals Procedures.
2. Product Data: Submit manufacturers’ product data, including product specification sheets, for products specified.
3. Shop Drawings: Submit shop drawings showing seating layout, seat-numbering scheme, chair sizes and aisle widths. Must meet all current ADA requirements.
4. Samples: Submit verification samples of finishes, colors and textures specified for each exposed material.
5. Quality Assurance Submittals; Submit the following:
6. Certificates: Product certificates signed by manufacturer certifying materials comply with specify performance characteristics and criteria and physical requirements.
7. Installer Qualifications: Submit certification indicating installer is qualified to install manufacturer’s seating. Must have a minimum of 5 years of experience.
8. Bidder Qualifications: Submit certification, prior to drawing completion, indicating site has been inspected for any conditions that may affect the assembly or installation of products required.

Section 1.04    WARRANTY

1. Project Warranty: Refer to “Conditions of the Contract” to project warranty provisions.
2. Manufacturer’s Warranty: Submit, for Owners acceptance:
3. Manufacturer’s standard warranty documents executed by authorized company official. Manufacturer’s warranty is in addition to, and not a limitation of, other rights Owners may have under Contract Documents.
4. Warranty period; Ten (10) year warranty on understructure and seating shells (when utilized) from defects of manufacture and workmanship, commencing on Date of Substantial Completion.
5. Warranty will be null and void if products are installed on flooring not meeting minimum structural requirements as specified by manufacturer.

Section 2.01    TABLE SYSTEM

1. Manufacturer: Navetta division of Shuttlesystem LLC
2. Product: Symmetra Fixed Table System
3. Product specifications
4. Pedestal Support – Construction: Pedestals shall be constructed of 11 gauge steel tubing of oval cross-section measuring 3.15” x 1.57”.
5. Floor mount – Pedestal shall be computer-controlled welded to a .25” thick steel base plate measuring 8” x 4” with four slotted holes for mounting pedestal to floor with anchor bolts.
6. Base cover – Base plate to be fully covered after mounting with two-piece cover constructed of injection molded toughened nylon, attached with two machine screws.
7. Table mount – Top mount bracket shall be constructed of 11 gauge steel with four attaching bolts allowing attachment to pedestal and adjustment for variations in floor surface to provide alignment of adjacent tabletops without shimming tops. Bracket shall provide six mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
8. Top shroud – Top mount bracket will be covered by shroud with rounded edges constructed of injection molded ABS, attached with machine screws.
9. Metal Finish – Metal components shall have powder-coat finish in finish specified.
10. Table Configuration – Table tops shall be designed to be assembled into continuous surface in straight, radius, or segmented configuration. Adjacent tops to be joined with two mechanical clamping fasteners. Tops shall have cutouts for tabletop power modules when specified. Manufacturer shall be FSC (Forest Stewardship Council) chain-of-custody Certified.
11. Table Top Construction – Table tops shall be nominal 1.25” thick warp-resistant construction with 1.125” particleboard center core sandwiched between .040” high pressure laminate top surface and phenolic backing surface. Assembly to be permanently bonded under continuous pressure in hot press.
12. Table Top Edge treatment – Edges shall be finished as specified, using 3mm PVC, “T” cross-section vinyl continuous molding, wood surface, or bonded resin edging.
13. Table Top Attachment – Table tops to attach to pedestal brackets with six #12 lag bolts.
14. Modesty Panel Construction – Modesty panels shall be constructed of .8” thick nominal particle board sandwiched with bonded high-pressure laminate as specified and phenolic backing sheet, or available perforated metal of specified material, pattern and finish.
15. Modesty Panel Attachment – Modesty panels shall interlock into machined recess in underside of table top surface and attach with supplied rigid metal brackets and hardware. Standard configuration provides .5” clearance between adjacent modesty panels, continuous configuration optional.
16. End Panel Construction – If specified, end panels shall be constructed of .8” thick nominal particle board sandwiched with bonded high-pressure laminate as specified and phenolic backing sheet, or available perforated metal of specified material, pattern and finish.
17. End Panel Attachment – End Panels shall attach with supplied rigid metal brackets and hardware.
18. Seat Support Mechanism – Seat support arms shall be constructed of 11 gauge oval steel tubing formed to a radius, with industry-standard taper receiver to accept chair cylinder. Arms on either side of the support pedestal shall pivot independently from a steel kingpin mounted in a die cast aluminum housing with powder coat finish. A field-adjustable torsion spring shall be implemented to automatically return the seat adjacent to the table top when not occupied. Must meet static load test requirement of 600 lbs. Auto-height auto-return seat cylinder allowing seat height adjustment, chair rotation and center return. Height adjustment mechanism and cylinder utilize precision taper fit, which eliminates requirement of tools and set screws.
19. Seat Specifications – A large selection of standard seats are available with the Symmetra Plus system, and virtually any other seat can be used with the system, including plastic, mesh back, and wood construction, upholstered or not, as the customer prefers. See specified seat documentation for detailed specification. All seats spin 360 degrees.

Section 3.1      MANUFACTURER’S INSTRUCTIONS

1. Comply with manufacturer’s installation instructions, including bulletins, product catalog, installation instructions and product carton instructions for installation.

Section 3.2      EXAMINATION

1. Site Verification: Prior to installation verify, with installer present, that substrates and conditions comply with the requirements for construction tolerances and materials properties as they affect anchors and fasteners and location of junction boxes.
2. Repair: Do not proceed until unsatisfactory components or facility conditions have been corrected.

Section 3.3      INSTALLATION

1. Installation: Install following manufacturers printed instructions for installation and using manufacturer recommended hardware and fasteners. Tables in curbed rows shall be installed at smooth radius.
2. Repair: Repair minor abrasions and imperfections in painted surfaces with a coating that matches the factory- applied finish.

Section 3.4      CLEANING AND PROTECTION

1. Cleaning: Clean Product in accordance with manufacturer instruction prior to Owner’s acceptance. Remove construction debris, including cartons from project site and legally dispose of debris.
2. Protection: Protect installed product and finished surfaces from damage during construction.

1.01 SUMMARY

1. Section includes: Auditorium Seating.
2. Manufacturer’s Fixed Auditorium Seating with Tablet Arm.
3. Extent: Extent of the fixed seating as indicated on drawings and as specified herein including product data sheets.

1.02 PRODUCT DESCRIPTION

Seat Requirements:

1. Chair: Deliver and install a fixed seat auditorium seat with gravity uplift seat and optional anti-panic tablet arm in accordance with drawings.
2. Dimensions are nominal and are based on the current product information available.

1.03 SUBMITTALS

1. General: Submit listed submittals in accordance with “Conditions of the Contract”  and Division 1 Submittals Procedures section.
2. Product Data: Submit manufacturer’s product data, including product specification sheets, for specific products.
3. Shop Drawings: Submit shop drawings showing seating layout, seat-numbering scheme, chair sizes and aisle widths.
4. Samples: Submit selection and verification samples of finishes, colors and textures for each exposed material.
5. Quality Assurance Submittals; Submit the following;
   • Certificates: Product certificates signed by manufacturer certifying materials comply with specify performance characteristics and criteria and physical requirements.
   • Installer Qualifications: Submit certification indicating installer is qualified to install manufacturers seating.
   • Bidder Qualifications: Submit certification, prior to drawing completion, indicating site has been inspected for any conditions that may effect the assembly or installation of products required.

1.04 WARRANTY

1. Project Warranty: Refer to “Conditions of the Contract” to project warranty  provisions.
2. Manufactures Warranty; Submit, for Owners acceptance, manufacturers standard warranty documents executed by authorized company official.
3. Manufactures warranty is in addition to, and not a limitation of, other rights Owners may have under Contract Documents.
4. Warranty period; (10) year warranty on understructure and shells from manufacture defect and workmanship, commencing on Date of Substantial Completion.

2.01 SEATING/TABLE SYSTEM

PRODUCT DESCRIPTION

1. Seat: formed on a high impact injection polypropylene frame with five serpentine springs and polyurethane cold molded anatomic cushion. Gravity self-rising system mounted on an injected high impact polypropylene structure. Pivot connection is a 5/8” round steel axle, with two side wings supports stamped with 7 gauge steel. Two inner supports stamped in 11 gauge steel. The bottom is protected by an injected high impact polypropylene cover which is textured on the outer face. Center to center seat sizes in 19”, 20”, 21”, 22”, 23”.
2. Back: polyurethane cold molded cushioning, with an ergonomically shape attached on an integral base made of high impact injection polypropylene, structured with multi-ribbed on the inner side and textured on its outer side. Featuring with two folded wing brackets made of 14 gauge steel to be attached to the center standards and aisle ends and has a rear back cover made of injected high impact polypropylene which is textured on the outer face. Center to center back sizes in 19”, 20”, 21”, 22”, 23”.
3. Side/Arms: Internal support structure steel plate painted with powder coat in aluminum or anthracite. Side panels available with fabric upholstery, laminate or wood. Armrest in polypropylene, solid wood or upholstered with non-deformable polyurethane foam.
4. Pedestal Supports: center and sides made of rectangular section tube of 1” x 3” 14 gauge. Back support in 14 gauge, seat support in 7 gauge, arm rest support 14 gauge, foot plate to be fixed on floor in 11 gauge steel.
5. FINISH: The metal parts previously degreased and phosphatized, are protected by EPOXICA and micro-sprayed thermoplastic painting, with electrostatic equipment and oven baked up to 200°C.
6. Tablet Arm: Tablet is MDF construction with laminate finish. Tablet shall be 11.75” wide by 10.25” deep.  3

3.01 MANUFACTURERS INSTRUCTIONS

1. Comply with bulletins, product catalog, installation instructions and product carton instructions for installation

3.02 EXAMINATION

1. Site Verification: Prior to installation verify, with installer present, that substrates and conditions comply with the requirements for construction tolerances.
2. Repair: Do not proceed until unsatisfactory conditions have been corrected.

3.03 INSTALLATION

1. Installation: Install following manufacturers printed instructions for installation and using manufacturer recommended hardware and fasteners. Chair and tables in curbed rows shall be installed at smooth radius.
2. Adjustments: Adjust seat mechanism to ensure seats in each row are aligned when in the upright position.
3. Repair: Repair minor abrasions and imperfections in painted surfaces with a coating that matches the factory- applied finish.
4. Replace: Replace any fabric damaged during installation.

3.04 CLEANING AND PROTECTION

1. Cleaning: Clean Product in accordance with manufacturer instruction prior to Owner’s acceptance. Remove construction debris, including cartons from project  site and legally dispose of debris.
2. Protection: Protect installed product and finished surfaces from damage during construction.

Section 1.01    SUMMARY

1. Table systems
2. Fixed Table: Symmetra System
3. Extent: Systems to be as indicated on drawings and as specified

Section 1.02    PRODUCT DESCRIPTION

1. Seat/Table Requirements:
2. Pedestal: provide table and supports providing fixed work surface with open access, supported by pedestals.
3. Power and Data Distribution System: Modular data and electrical system housed in flexible conduit. All power system components shall be UL approved, including the steel pedestal table leg used for power entry, which shall be certified as a “UL Recognized Component,” and will have appropriate labeling documenting that approval.

Section 1.03    SUBMITTALS

1. General: Submit listed submittals in accordance with Contract and standard Submittals Procedures.
2. Product Data: Submit manufacturers’ product data, including product specification sheets, for products specified.
3. Shop Drawings: Submit shop drawings showing seating layout, seat-numbering scheme, chair sizes and aisle widths.
4. Samples: Submit verification samples of finishes, colors and textures specified for each exposed material.
5. Quality Assurance Submittals; Submit the following:
6. Certificates: Product certificates signed by manufacturer certifying materials comply with specify performance characteristics and criteria and physical requirements.
7. Installer Qualifications: Submit certification indicating installer is qualified to install manufacturer’s seating.
8. Bidder Qualifications: Submit certification, prior to drawing completion, indicating site has been inspected for any conditions that may affect the assembly or installation of products required.

Section 1.04    WARRANTY

1. Project Warranty: Refer to “Conditions of the Contract” to project warranty provisions.
2. Manufacturer’s Warranty: Submit, for Owners acceptance:
3. Manufacturer’s standard warranty documents executed by authorized company official. Manufacturer’s warranty is in addition to, and not a limitation of, other rights Owners may have under Contract Documents.
4. Warranty period; Ten (10) year warranty on understructure and seating shells (when utilized) from defects of manufacture and workmanship, commencing on Date of Substantial Completion.
5. Warranty will be null and void if products are installed on flooring not meeting minimum structural requirements as specified by manufacturer.

Section 2.01    TABLE SYSTEM

1. Manufacturer: Navetta division of Shuttlesystem LLC
2. Product: Symmetra Fixed Table System
3. Product specifications
4. Inner Pedestal Support – Construction: Pedestals shall be constructed of 11 gauge steel tubing of oval cross-section measuring 3.15” x 1.57”.
5. Inner Pedestal Support Floor mount – Pedestal shall be computer-controlled welded to a .25” thick steel base plate measuring 8” x 4” with four slotted holes for mounting pedestal to floor with anchor bolts.
6. Inner Pedestal Support Base coverBase plate to be fully covered after mounting with two-piece cover constructed of injection molded toughened nylon, attached with two machine screws.
7. Inner Pedestal Support Table mount – Top mount bracket shall be constructed of 11 gauge steel with four attaching bolts allowing attachment to pedestal and adjustment for variations in floor surface to provide alignment of adjacent tabletops without shimming tops. Bracket shall provide six mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
8. Inner Pedestal Support Top shroud – Top mount bracket will be covered by shroud with rounded edges constructed of injection molded ABS, attached with machine screws.
9. Outer Pedestal Support – Construction: Pedestals shall be constructed of paired extruded structural aluminum columns measuring 2.3” x 2.2”, with heavy-duty .09” wall thickness and internal reinforcing ribs measuring .20” thickness.
10. Outer Pedestal Support Floor mount – Pedestal shall be rigidly mounted to a .25” thick steel base plate measuring 11.5” x 2.5” with four holes for mounting pedestal to floor with anchor bolts.
11. Outer Pedestal Support Side Cover – Floor mounting hardware and top mounting hardware to be fully concealed by two 7.0” wide aluminum extruded removable panels.
12. Outer Pedestal Support Table mount – Top mount bracket shall be constructed of .25” thick steel plate with eight attaching screws allowing attachment to pedestal columns. Bracket shall provide four mounting holes for attaching table top and designed to accept optional power and/or data electrical system.
13. Metal Finish – Steel components shall have powder-coat finish in finish specified. Aluminum components shall have anodized finish or powder-coat finish in finish specified.
14. Table Configuration – Table tops shall be designed to be assembled into continuous surface in straight, radius, or segmented configuration. Adjacent tops to be joined with two mechanical clamping fasteners. Tops shall have cutouts for tabletop power modules when specified. Manufacturer shall be FSC (Forest Stewardship Council) chain-of-custody Certified.
15. Table Top Construction – Table tops shall be nominal 1.25” thick warp-resistant construction with 1.125” particleboard center core sandwiched between .040” high pressure laminate top surface and phenolic backing surface. Assembly to be permanently bonded under continuous pressure in hot press.
16. Table Top Edge treatment – Edges shall be finished as specified, using 3mm PVC, “T” cross-section vinyl continuous molding, wood surface, or bonded resin edging.
17. Inner Pedestal Support Table Top Attachment – Table tops to attach to pedestal brackets with six #12 lag screws.
18. Outer Pedestal Support Table Top Attachment – Table tops to attach to pedestal brackets with 4 #14 lag screws.
19. Modesty Panel Construction – Modesty panels shall be constructed of .8” thick nominal particle board sandwiched with bonded high-pressure laminate as specified and phenolic backing sheet, or available perforated metal of specified material, pattern and finish.
20. Modesty Panel Attachment – Modesty panels shall interlock into machined recess in underside of table top surface and attach with supplied rigid metal brackets and hardware. Standard configuration provides .5” clearance between adjacent modesty panels, continuous configuration optional.

Section 3.1      MANUFACTURER’S INSTRUCTIONS

1. Comply with manufacturer’s installation instructions, including bulletins, product catalog, installation instructions and product carton instructions for installation.

Section 3.2      EXAMINATION

1. Site Verification: Prior to installation verify, with installer present, that substrates and conditions comply with the requirements for construction tolerances and materials properties as they affect anchors and fasteners and location of junction boxes.
2. Repair: Do not proceed until unsatisfactory components or facility conditions have been corrected.

Section 3.3      INSTALLATION

1. Installation: Install following manufacturers printed instructions for installation and using manufacturer recommended hardware and fasteners. Tables in curbed rows shall be installed at smooth radius.
2. Repair: Repair minor abrasions and imperfections in painted surfaces with a coating that matches the factory- applied finish.

Section 3.4      CLEANING AND PROTECTION

1. Cleaning: Clean Product in accordance with manufacturer instruction prior to Owner’s acceptance. Remove construction debris, including cartons from project site and legally dispose of debris.
2. Protection: Protect installed product and finished surfaces from damage during construction.